Start your trial now! First week only $4.99!*arrow_forward*

Question

A Diesel cycle has a compression ratio of 22 and begins its compression at 85 kPa and 15°C. The maximum cycle temperature is 1200°C. Utilizing air-standard assumptions, determine the thermal efficiency of this cycle using variable specific heats.

Tagged in

Engineering

Mechanical Engineering

Find answers to questions asked by students like you.

Q: Investigate the complex potential f(z) = A cosh [π(z/a)],and plot the streamlines inside the region ...

A: Writing the complex potential function: Where A is a constant. Splitting the potential function i...

Q: As many as three axial loads each of magnitude P= 10 kips can be applied to the end of a W8 * 21 rol...

A: Given data as per question Magnitude of P = 10 kips

Q: A rigid container equipped with a stirring device contains 2.5 kg of motor oil. Determine the rate o...

A: Given: The mass of the motor oil, m = 2.5 kg The heat transferred to the oil, Q = 1 W The power give...

Q: *R17-8. The W200 × 46 wide-flange A992-steel column can be considered pinned at its top and fixed at...

A: Write the properties of A992 steel. Write the properties of the W200X46 flange.

Q: A coastal power plant takes in cooling water through avertical perforated manifold, as in Fig. . The...

A: Calculate the sink strength using the relation with the depth of water. Here, Q is the volume flow ...

Q: Refrigerant-134a is expanded isentropically from 600 kPa and 70°C at the inlet of a steady-flow turb...

A: Given Data: The inlet pressure of the refrigerant R-134a is P1 = 600 kPa. The inlet temperature of ...

Q: i need and detailed answer to a-d thankyou^^

A: The data given is, Length of blue car, Lb = 4.52 m Width of the road, w = 28 m Acceleration of blue...

Q: There are four additive terms in an equation, and their units are given below. Which one is not cons...

A: Click to see the answer

Q: Argon is compressed in a polytropic process with n = 1.2 from 120 kPa and 10°C to 800 kPa in a pisto...

A: Given: The initial pressure of the argon in the piston-cylinder device is P1=120 kPa The final press...

Q: Consider two houses that are identical in size. House 1 has outside walls that were built using a do...

A: As the wood is natural insulator so it will be more efficient than double layer brick. So, the house...

Q: A grist mill of the 1800s employed a waterwheel that was 14 m high; 480 L/min of water flowed onto t...

A: Given: The height of the water wheel is H=14 m. The volume flow rate of the water on the wheel is V=...

Q: Len is asked to design a small water pump for an aquarium. The pump should deliver 18.0 Lpm of water...

A: Given data

Q: Gasoline at 20°C flows at 105 m3/h in a 10-cm-diameterpipe. We wish to meter the flow with a thin-pl...

A: Given data: The discharge of the gasoline is Q=105 m3/h. The diameter of the pipe is d=10 cm. The pr...

Q: What is the main difference between the HEAC model and the IHAC model?

A: Hydrogen environment assisted cracking model (HEAC model) and Internal hydrogen assisted cracking mo...

Q: 15-59. The 5-Mg truck and 2-Mg car are traveling with the free-rolling velocities shown just before ...

A: Click to see the answer

Q: The L-shaped frame is made from two segments, each of length L and flexural stiffness EI. If it is s...

A: The moment due to distributed load about the point B is The vertical displacement of the point B is...

Q: *10-56. The shaft of radius c is subjected to a distributed torque t, measured as torquellength of s...

A: Given data: The length of the shaft is The radius of the shaft is The torque per unit length is The...

Q: Determine the moment reactions at the supports A and B. EI is constant.

A: Free Body Diagram for the given beam is

Q: The two forces act on a bolt at A. Determine theirresultant.(graphical solution)

A: Applying the graphical method First of all, a parallelogram with sides equal to P and Q is drawn. Th...

Q: 17-18. Determine the moment of inertia of the assembly about an axis perpendicular to the page and p...

A: Given data: *The mass of the block is m=3 kg. *The mass of the semi cylinder is mc=5 kg. *The radius...

Q: A 10-mm-diameter rod has a modulus of elasticity of E = 100GPa. If it is 4 m long and subjected to a...

A: Given: The diameter of the rod is d=10 mm The length of the rod is L=4 m The axial load on the rod i...

Q: A rigid plate, having a weight of 100 lbs acting at its center, is connected to a 'ball and socket' ...

A: Click to see the answer

Q: The jib crane supports a load of 750 lb from the trolly which rides on the top of the jib. Determine...

A: Click to see the answer

Q: P7-5. The lever is held to the fixed shaft using the pin AB. If the couple is applied to the lever, ...

A: Click to see the answer

Q: Ethane at 10 MPa and 100°C is heated at constant pressure until its volume has increased by 60 perce...

A: Given data To determine te final temperture using idael gas equation of state and compressibility f...

Q: Use the rectangular component method to solve the fol- lowing problems. Determine the magnitude R of...

A: Given data: F1 = 160 N F2 = 180 N Considering the given diagram:

Q: The dry bulb and wet bulb temperatures of a room are measured as 30C and 20C, respectively. After mo...

A: The two points are shown on the psychometric chart below. Initial point -1 Final point -2

Q: *R5-8. Determine the resultant forces at pins B and C on member ABC of the four-member frame. -1.25 ...

A: The free-body diagram of the frame showing the reactions at joints can be sketched as follows,

Q: Two identical hockey pucks are moving on a hockey rink at the same speed of 3 m/s and in perpendicul...

A: By using principle of impulse momentum For puck A (in Y direction) For puck B (in Y direction) Fo...

Q: 12–141. A package is dropped from the plane which is flying with a constant horizontal velocity of v...

A: Given: The horizontal velocity of plane, vA,x = vB,x = 150 ft/s The height of plane initially, H = 1...

Q: 15-1. Determine the impulse of the force for t=2 s. 200 N

A: Given: The force acting on the block is F=200 N The time for which the force is acting on the block ...

Q: How to steam flow control in Hydroelectric Plants

A: A hydroelectric plant is operated by Water. There is not steam in hydroelectric plant. Steam is use...

Q: Four signs are mounted on a frame spanning a highway, and the magnitudes of the horizontal wind forc...

A: Determine the magnitude and the point of application of the resultant of the four wind forces: Let u...